Calculations are an important part of planning around a construction project. From concept to completion of the project calculation is a tool to try to predict the actual cost. During the production stage in particular, deviations occur which makes the actual cost different from the calculations.This thesis is done in collaboration with JM Residential Stockholm. The study includes a cost follow-up in which a comparison was made between the calculated production cost and actual cost for the five projects. The aim of the study was to observe the most common reasons that a project deviates from the calculated production cost and then summing these causes in a number of categories.

The E-department at GETRAG All Wheel Drive in Köping have problems with the efficiency on parts of their production equipment. The equipment with the most significant efficiency problems are four automated multifunctional production cells that produces housing for rear drive units. The major part of the problem is the large amount of small stops that causes the low efficiency.The department already worked with logging of interruptions and efficiency calculations before this project started. However this work was not done to the extent considered necessary for a systematic follow-up of the interruptions.The aim of this paper is to point out a more effective and systematic way to work with logging of interruptions and the follow-up. In addition the equipment were studied with a method for efficiency calculation that ? if used properly- is a more powerful and a visually better method than the one used by the company today.As the initial current state analysis of the equipment was made a lack of documented knowledge about the equipment was discovered.

Skanska is using work schedules that are specifically designed for employees in the production. These work schedules are called best practice. These are guides containing technical descriptions, design references, capabilities, etc. for work activities. This support function facilitates the work preparation and planning of future work.

This examination report is a part of a program for Industrial organisation and Economics with specialization in Logistics and Management at Jönköping University. The report contains an analysis of the internal material handling at Kongsberg Automotive, and also an improvement proposal for a new material handling system.The aim with the report is to find a better material handling system and also make an analyse of the existing system. The goal is to shorten the distance for the operators when they order material, and also to increase the productivity.The investigation methods for the report have for the most part consisted of observations and interviews of key-persons who daily work in the production. During some time the actual material handling-system has been observed and some shortcomings have been discovered, and these are also discussed in the report.The shortcomings that have been discovered are for once the indistinct signal that should signal need of material in the production. Some other activities have also been discovered that does not bring any value into the final products.

The organic farmland is increasing all the time and the goal is that 15 % of the Swedish farmland will be in organic production in year 2010. The organic production needs new and more effective ways to control weeds, and there is the row harrowing coming as a good complement to the conventional weed harrowing. In this experiment is weed harrowing whit different row spaces and row harrowing with a spacing of 25 cm compared. Then are the weed picked and the weight taken of them. The yield is compared in the 7 different ways of treatment. The results is not showing any significant differences in yield even when the row spacing is 25 cm instead of 12,5 cm. Even the spring wheat that is a sensitive crop and has bad tillering is doing well in this experiment. Now with modern technology where the row harrow is controlled by a camera that making the row harrow to follow the rows is it the soil coverage of the crop that is the limit for the speed. With wide machinery is the very good coverage even with a row harrow..

The purpose with this bachelor thesis is to identify risks and insufficiencies concerning the production at WilloMaskin AB. The project is limited to only 4 machines, where theories as ?OEE? (overall equipment efficacy) should be illuminated and analyzed. The theory of ?Single Minute Exchange of Die? is also presented.The method used in this project is mostly based on qualitative studies but also quantitative studies are presented.

Quality assurance means to systematically work for better understanding of the customers needs, demands and expectations. The goal for this study was to investigate how quality can be assured in the job follow up that is made by forestry contractors after soil scarification and planting. The study consisted of a description over the current follow up process at SCA forest AB Jämtlands forest administration, analysis of current follow up situation and an investigation of follow up process made by contractors in other line of business. The first step was a statistical comparison where the own follow up made by contractors were compared with follow up made by SCA them selves over 100 stands. Two soil scarification contractors and two planting contractors carried out the silvicultural measures. The results showed that significant differences between a number of quality factors measured, for example number of approved plants or approved scarification points, average score on stand and number of totally planted plants.

This bachelor thesis examines and discusses the question: "How can graphics for newscasts be adapted to follow technological developments in various media and increase its informative quality?" The work was performed on Swedish Television's own graphic department, SVT design in order to examine how news graphics need to be developed to follow the technological changes in media. The production resulted in a news graphics concept divided into three parts. Two of the sections show examples of how graphics can be adapted according to platform and the third section shows examples of news graphics that are produced at SVT Design by me. The bachelor thesis focuses on the development of technology in the media and examines areas such as interactive solutions, news graphics and the traditional television media..

This bachelor thesis examines and discusses the question: "How can graphics for newscasts be adapted to follow technological developments in various media and increase its informative quality?" The work was performed on Swedish Television's own graphic department, SVT design in order to examine how news graphics need to be developed to follow the technological changes in media. The production resulted in a news graphics concept divided into three parts. Two of the sections show examples of how graphics can be adapted according to platform and the third section shows examples of news graphics that are produced at SVT Design by me. The bachelor thesis focuses on the development of technology in the media and examines areas such as interactive solutions, news graphics and the traditional television media..

Lean Production is used by many manufacturing companies. Companies in process industries do not use Lean Production to the same extent today. This is part of the report's issue to explore how Lean Production can be applied to a company in the process industries.The investigated company is a processing company that manufactures various types of foil. The company wishes to streamline its production and has therefore asked the authors to examine if Lean Production can offer the company improvements in their production. Lean Production value stream mapping tool has been selected to identify and analyze the current state of two of its products in production.

On today?s competitive market, it is difficult to achieve profitability trough high prices on manufactured products. Profitability must be obtained through low manufacturing costs, high quality and short lead times. One of the companies on the market is Sandvik Coromant, manufacturer of tools and chips for metal cutting. This master thesis investigates the methods of manufacturing for boring bars at the manufacturing unit GVH4 at Sandvik Coromant in Gimo, Sweden.

Due to the obvious fact that one can never be hundred percent sure of what's hiddenunder the ground surface, construction work is naturally hard to project.However, many of the work methods are executed in the same way on variousprojects. The department of construction work at JM AB region öst describes a lackof follow-ups and feedback between the calculators and production managers.In this thesis we have studied the communication between these groups and alsohow they share experiences and knowledge. In order to get the full pictureof the day-to-day operations we used three methods to gather information. Studyingliterature gave basic knowledge of theories about feedback, and thenecessity of working with giving feedback. In order to understand the process ofconstruction work we made several interviews, both structured and nstructured.

The aim of this thesis is benchmarking of the program, based on dynamic programming, that earlier was written to imitate the production planning at TSS.This thesis starts with a chapter about the construction of the DP-program, a shorter description of one and each of the program parts and also a list over the in- and output data in each program part. The DP-program consists of six linked MATLAB-files that together produce an optimized production plan for the different planning groups at TSS. The program reads in and reformat the given data and optimize the production of the articles in one group. Finally it compounds all article production plans and give us a production alternative.After running the program with new data the result shows, resembling with previous results, that TSS could be able to make some distinct cost-savings. According to the program, a 50 % decrease of TSS production costs is possible. .

This report contains results of our study at CTC in Ljungby. CTC produces heating products such as boilers, heat pumps and additional products to their heating systems.The purpose of the report is to make a proposal how CTC will supply their new production line for heat pumps with materials. The proposal includes a production layout and a scheme for how to place the material in the production storage.The new production line will produce two different products and both of them have several variants. The line will also have a mixed flow, so the products can be produced in a random order. These conditions demand that the production line has great flexibility and that the material to all the variants can be stored in the production storage.With these conditions as input we made a layout proposal to the company.

In Sweden, selection for leanness in pigs has been going on for almost a century. This sometimes results in gilts and sows being too lean and consequently in a risk for reduced reproduction and health status. The Swedish recommendation includes that gilts should be mated after seven months of age, after one documented oestrus, at 120-140kg live weight and with a backfat thickness of 16-20mm. Five gilt producing herds were visited and records of age, heart girth (for weight estimation), body condition (visual estimation), backfat thickness and exterior were made. The same records were also taken in four gilt buying herds on newly purchased gilts.